Note: Charger Master V2 is compatible with LiHV mode. So after you update the charger with LiHV mode, please replace Charger Master V1 with V2 in your PC. Please follow below steps to do the update, 1. Connect the charger and PC with USB cable. Power on the charger. Start the update program and click “update” to start the process. Internal and external temperature monitoring; Overcharge and overdischarge. Imax B6 Charger Pc Software. Hi, you can indeed connect the charger to the computer (to monitor. Imax B6 Charger Manual Download. Imax B6 Charger Software Download. The process of discharging, the eXtreme 605 can monitor. How to install the pc monitoring software for the imax b6/ac v1 & v2.
I briefly mentioned that the iMax B6 Quattro charger has a computer interface. I already was disappointed that the interface is per charger and only half of the chargers have it. Another disappointment came when I tried the software.
The provided software only supports the bare minimum, both in functionality and user interface:
Imax B6 Charger Pc Software Free
It’s Windows only, there is no zooming functionality and no exact value readout. The file format for the “Log file” is some obscure binary format. In short, inadequate.
The hardware
The provided communications hardware is decent. It’s a small ~1*3cm PCB with a female mini-USB connector on one side and a pigtail leading to a female Futaba J-type connector on the other side, which plugs into the charger.
This board is actually just an USB-to-Serial convertor by SiLabs. SiLabs provides drivers for Windows, Mac (local copy) & Linux
(local copy).
The protocol
Imax B6 Charger Problems
The protocol seems to be fairly simple. Just connecting the charger to PC already produces a stream of bytes. There is no need for the computer to send any requests. I use a simple perl script that opens the serial port in the correct mode and produces the read bytes on STDOUT. The bytestream consists of 74 byte long messages wrapped in curly braces (`{` (0x7b) and `}` (0x7d)).
The last two bytes each contain 4 bits of the 8-bit checksum of the first 72 bytes:
The 72 data-bytes all have their high 0x80 bit set, they only contains 7 bits of data each. For the rest of this discussion, I’m only referring to the lower 7 bits of each byte. Here are the data-pieces that I discovered. Byte numbers start at 0 for the first data byte (i.e. 0x9e in the example above).
Imax B6 Quattro Charger
- Byte 7 contains part of the state
- bit 0x01 is set when charging, clear when discharging
- bit 0x10 is set when cycling, clear when single charging or discharging
- Byte 8 contains the set NiCd charge current in dA
- Byte 9 contains the set NiCd discharge current in dA
- Byte 12 contains the set NiMH charge current in dA
- Byte 13 contains the set NiMH discharge current in dA
- Byte 14, bit 0x01 contains the cycle mode, set for {Charge,Discharge}, clear for {Discharge,Charge}
- Byte 15 contains the cycle count
- Byte 16 contains the set Li__ charge current in dA
- Byte 17 contains the set Li__ charge cell count
- Byte 18 contains the set Li__ discharge current in dA
- Byte 19 contains the set Li__ discharge cell count
- Byte 20 contains the set Pb charge current in dA
- Byte 21 contains the set Pb cell count
- Byte 22 contains the mode:
- 0x80: Config
- 0x81: Li
- 0x82: NiMH
- 0x83: NiCd
- 0x84: Pb
- 0x85: Save
- 0x86: Load
- Byte 23 contains the running state: bit 0x01 is set when running, cleared when standby
- Byte 24 & 25 contain the set NiMH discharge voltage in daV and cV
- Byte 26 & 27 contains the set NiCd discharge voltage in daV and cV
- Byte 32 & 33 contain the actual current in A and cA
- Byte 34 & 35 contain the catual voltage in V and cV
- Byte 40 & 41 contain the input voltage in V and cV
- Byte 42 & 43 contain the charge in dAh and mAh
- Bytes 44 & 45; 46 & 47; 48 & 49; 50 & 51; 52 & 53; 54 & 55 contain the individual Li__ cell voltages in V and cV
- Byte 69 contains the time in minutes
Or if you’re lazy, just feed in the bytes into this perl script.
Pinout of IMAX B6 Balance ChargerIMAX B6 Balance Charger. PROGRAM FLOW CHART.
OPERATION SKYRC B6AC V2 is the upgraded version for well-known IMAX B6AC. Compared ..
(See the wiring diagram below .). IMAX B6 charger (original and clone) - open source firmware.
Projects that are not Schematic diagram: If not is there a circuit we can build with resistors/ pots to connect a power supply and calibrate the 6 balance outputs?. Your schematic is not correct, because the chargers expect a balancing connector with n+1 contacts: negative plus positive of each element.
Help! IMAX B6 Schematic Batteries and Chargers.
All of this circuit is the Charge Voltage Supply and Charge Current Regulation. The design.Thank you for purchasing the B6AC LiPo Balance Charger by schematron.org product is a rapid charger with a high performance microprocessor and specialized operating software. Please This diagram shows the correct way to connect your battery to the B6ACcharger while charging in .
24v Battery Wiring Diagram 24 Volt Golf Cart Battery Rv Deep Cycle Battery Sears 36 Volt Lester Golf Cart Battery Charger Pro Nautic 24v Battery Chargers schematron.orgb6 If obtain in a jam, this kind of is the thing that's in order to get you of the situation. The balance wire attached to the battery must be connected to the charger with the black wire aligned with IMAX B6 Ultimate will be operated with the default value of the essential user settings when it is connected the negative marking.
Take care to maintain correct polarity! (Wiring diagram: see below.) to a 12V battery for the first time.
Aug 25, · Help! IMAX B6 Schematic Batteries and Chargers.
Has anyone ever seen a parts layout for the B6? Someone assigned component designators to each part, which would be a lot more helpful if there was a component placement drawing.
Pinout of IMAX B6 Balance ChargerIMAX B6 Balance Charger. Pinouts / Devices / Connectors. serial interfaces pinouts.
IMAX B6 Balance Charger pinout. Various Electronic Devices > Imax pinouts.
Bookmark; Ask a question search in ebay for USB RS TTL and you' ll find adaptors for about $2. Simply connect GND-GND and TX from IMAX B6 to RX of 3/5(3).Pololu 3pi robot simplified schematic diagram.# 24v Battery Wiring Diagram #